WU #1

​

1. Where can you look for assignments if you are absent? 

2. What grade must you recieve on a safety test in order to use machinery?

3. Name the finger rules on the:

   • Band Saw

   • Scroll Saw

   • Drill Press

   • Router

   • Sanders 

​

WU #2

​

1. Name the finger rules on the 

   • Table saw ​

   • Radial Arm Saw

   • Panel Saw 

   • Jointer 

   • Planer 

2. Can you operate the planer and the planel saw at the same time? Why?​

3. When should safety glasses be worn in the shop? 

​

WU #3

​

1. What is the finger rule on the jointer?

2. Name 2 different kinds of wood we have used in the past in this class. 

3. What is the difference between sheet goods and lumber?

​

WU #4

​

1. What dimension is standard lumber sold at?

2. What is the actual size of a 2 x 4 

3. What is a soft wood?

​

WU #5

​

1. What are 2 ways to identify red oak?

2. How can you tell the difference between hard maple and soft maple?

3. Name 2 types of sheet goods. 

​

WU #6

​

1. What are 3 types of joints we will be using on the table?

2. What will be the hardest part of the table project in your opinion?

3. Name 3 tools we might use on the table project. 

​

WU #7

​

1. How many steps should be in a table POD?

2. What do you think the overall cost to build the table is going to be?

3. How many parts are on the table?

​

WU #8

​

1. What is a section view on a draft?

2. What is important to remember about CAD drafting?

3. What is calculating for waste?

​

WU #9

​

1. How many steps are in the Table POD?

2. What are hidden lines?

3. Do we have hidden lines in the table plans?

​

WU #10

​

1. Which came first the mortise or the tenon?

2. What saw might you use to cut your tenons for the legs?

3. What will be the hardest part of the table project?

​

WU #11

​

1. What is one important thing to remember about gluing up your leg pieces?

2. What do you do after the leg glue up?

3. how many clamps were needed for the leg glue up, and what type of clamps did you use?

​

WU #12

​

1. How deep is the mortise on the legs?

2. How wide should the aprons be on the table project? 

3. What is a domino machine? 

​

WU #13

​

1. How do you keep an object glued perfectly flat?

2. What type of clamps would you use for the Front Apron glue up? 

3. What machine will you use for tenons?

​

WU #14

​

1. What is a grinder?

2. When would you use a grinder in this class?

3. What is sharpening important?

​

WU #15

​

1. What is the finger rule on the grinder?

2. Why is it important to dip chisels while sharpening?

3. How do you know if a chisel is nice and sharp?

​

WU #16

​

1. When would you use a domino in this class?

2. What are 3 different domino sizes? 

3. Name one machine that is similar to a domino machine. 

​

WU #17

​

1. Draw a mortise and tenon joint. 

2. How are dominos and tenons alike?

3. What is the finger rule on the Domino Machine?

​

WU #18

​

1. What size domino will you use for your inside aprons?

2. What makes a domino joint strong?

3. Draw a groove. 

​

​